Did you know?

Remove the lug nuts. Pull off the wheel. step 2 :Removing the Rear Strut Assembly. 1:16. Remove the 15mm bolt on the sway bar link with a 15mm wrench and 5mm Allen key. Remove the bolt connecting the lower control arm to the steering knuckle. Remove the bottom strut bolt with a 21mm wrench and 21mm socket and 1/4 inch breaker bar.Step 3: Remove associated parts. Step 4: Support the strut and remove the top nuts. Support the bottom of your strut with your floor jack. place it directly underneath your lower control arm, or your ball joint. I chose to place it under the lower ball joint as it was the lowest point.OEM Frontier / Xterra Rear Shock Replacement Hardware Kit. $18.68. Nissan Frontier Shock Skids by Z1 Off-Road. ... OEM Bolt that is used to mount the lower part of the shock/strut in the front and rear of your 2005+ Nissan Frontier (D40) or 2005-2015 Nissan Xterra (N50). ... Must have if your changing struts. Why waist time with old bolts. Buy ...

Follow along to learn how to properly remove and replace a strut assembly. This video is sponsored by PRT.Shop Owner: https://www.shopownermag.comPRT: https:...Pry off the center cap with a flat blade screwdriver. Loosen the lug nuts with the vehicle on the ground. Raise the vehicle with a floor jack. Secure the vehicle on jack stands. Remove the lug nuts. Pull off the wheel. step 2 :Removing the Strut Assembly. 1:36. Pry off the flexible brake hose from the clip.There are three bolts that hold the shock support to the chassis and a through bolt at the bottom of the shock. Pull the old one out and pop the new one in, and you’re done. With the new shock in place, make sure everything’s torqued back to factory specs.Thread Tools. Strut Replacement. I've searched both forums extensively and am unable to find any specific procedures or diagrams of the strut replacement on the G8. Maybe the job is that simple, but does anyone have: 1) Torque specs 2) Detailed Procedures 3) Diagram (s) At 30k the stock GT struts are just way too soft - no strut leaks (yet) or ...Remove wheels, set aside. Remove brake line clip, using flat blade screwdriver. Using combination wrench (open end) to secure the nut, loosen both main (19mm) bolts, then remove one of the bolts. Leave the other bolt in for now, to hold the strut in place. Climb in vehicle, remove the three nuts from the strut top.

Install the upper strut mount nut (1), using the CH 49375 wrench and tighten to 45 N·m (34 lb ft). Insert the front strut in the knuckle. Install the steering knuckle nuts and bolts (1) and tighten to 90 N·m (66 lb ft) +60-70 degrees. Install the stabilizer shaft link nut (1) and tighten to 65 N·m (48 lb ft).A loaded strut is a complete, bolt-on replacement that can be easily installed at home to restore handling to factory settings. A bare strut reuses the original coil spring so it's cheaper but will require tool rentals or shop time and usually additional replacement parts. Strut replacement is generally recommended between 50-100k miles and ... ….

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Strut bolt replacement. Possible cause: Not clear strut bolt replacement.

I needed to replace a strut bearing on my 2004 9-3 with 72k miles. Ive owned the car since new, and in the last few months, I noted the strut binding when turning to the right. ... Pull the mount and the bottom bolt, then attach the shock to a new mount (or reuse), torque the top nut to 24 ft-lb, then install the mount, align the bottom holes ...Today I replaced the strut assemblies in a 2005 dodge dakota that is four wheel drive.When it comes to assembling and tightening bolts in various applications, using a bolt torque chart is an essential tool. A bolt torque chart provides the recommended torque values...

Front strut replacement 2007 Chevrolet Aveo LS struts Install Remove Replace How To Change. 2020 has really shown me I needed to be better prepared for the ...The shock absorbers on your vehicle dampen and absorb road conditions by controlling suspension motion while driving. Struts are similar to shock absorbers internally, but also provide structural support for your vehicle’s suspension and wheel alignment. Both help to provide a smoother and more comfortable drive, and ensure your vehicle ...

digital perm san diego FRAM Ultra Synthetic Automotive Replacement Oil Filter, Designed for Synthetic Oil Changes Lasting up to 20k Miles, XG3614 with SureGrip (Pack of 1) $8.97. Allmost for Compatible with 2005-2015 Toyota Tacoma Fender Flare Retainer Clip 75495-35010 75397-35010 (Pack of 38) $8.99. factory key fob replacementbnsf train times Remove the pinch bolt that holds the strut in the knuckle. Remove the pinch bolt that secures the lower ball joint to the knuckle. Remove the tie rod. Next, remove the three bolts that secure the upper strut mount to the vehicle. To remove the strut, pull down on a lower control arm to pull the stud of the ball joint from the bore. 4runner steel wheels Take the lower spring perch insulator and put it on the new strut reassemble in reverse order. Loosely support the strut using the top screws and start threading the bottom 27mm bolts. Once everything is properly positioned, tighten and up the screws and you're good to go. penske truck tow dollymyadpcomrs3 log Pull off the wheel. step 2 :Removing the Sway Bar Links. 1:17. Grab the back side of the sway bar with locking pliers. Remove the 17mm nut from the sway bar link. Remove the sway bar link from the strut. step 3 :Removing the Front Strut. 1:51. Remove the 13mm bolt securing the flexible brake hose and ABS harness. acv and baking soda for weight loss Start by soaking the strut flange nuts and bolts with rust penetrant. Then pop the hood and spray the strut-tower mounting nuts. Spin two lug nuts onto the studs and tighten to secure the rotor to the hub. While they're soaking, mount the angle gauge to the top of the rotor and note the angle. Step 4.Buy Now!New Strut & Spring Assembly from 1AAuto.com http://1aau.to/ia/1ASTS01645This video shows you how to install front struts on your 2009-2013 Honda Fit.... obituaries in akron ohioadp employee portal sign inhome depot gm salary Watch this video for a tip on how to cut metal bolts and machine screws to length cleanly and easily without damaging the threads. Expert Advice On Improving Your Home Videos Lates...The torque strut mount naturally breaks down and weakens. A worn out torque mount needs to be replaced immediately because it can cause further damage to many components attached to the engine and transmission, including sensors, wiring connectors, gaskets, hoses. Excessive movement in the engine will cause premature failure to these components.